LKS West Instruments Sdn Bhd - Shah Alam, Malaysia

These level gauges are particularly suitable for liquids:
- Colorless
- Very Fluid
- Non-corrosive for glasses (e.g. ammoniacal solutions, trichlorethylene, water steam up to 32bar, etc.)

Bicolour level gauge will parallel glasses.
Working Principle:
It is a variation of transparent level gauge, however equipped with two reflex glasses and a back illuminator, fitted with suitable coloured fitters. The reading is given by the contrast between the bright colour (usually:red) of fitters in the lower part containing liquid and the colour of upper part of visible window.

The drawing shows a typical Reflex Glass Level Gauge.
This instrument consists of a metal body, machined to have an internal chamber and one or more front windows (on one side
only of the gauge).
On each window a special high resistance plate reflex glass is fitted with sealing joint and metal cover plates hold by bolts
and nuts.
The chamber is connected to vessel with cross fittings and flanged, threaded or welded ends. Usually, between the instrument and its connecting ends, valves are fitted to consent shut-off piping and to disassemble the level gauge without to empty the vessel. Drain valves can also be fitted to cross
fittings device.
To avoid leakage in case of glass breakage, safety ball-check device can be provided.

Working Principle:
Reflex level gauges working principle is based on the light refraction and reflection laws.
Reflex level gauges use glasses having the face fitted towards the chamber shaped to have prismatic grooves with section angle of 90°. When in operation, the chamber is filled with liquid in the lower zone and gases or vapors in the upper zone; the liquid level is distinguished by different brightness of the glass in the liquid and in the gas/vapor zone. The reflex level gauges do not need a specific illumination: the day environmental light is enough. Only during the night an
artificial light must be provided.

These level gauges are particularly suitable for liquids:
- Colorless
- Very Fluid
- Non-corrosive for glasses (e.g. ammoniacal solutions, trichlorethylene, water steam up to 32bar, etc.)

Bicolour level gauge will parallel glasses.
Working Principle:
It is a variation of transparent level gauge, however equipped with two reflex glasses and a back illuminator, fitted with suitable coloured fitters. The reading is given by the contrast between the bright colour (usually:red) of fitters in the lower part containing liquid and the colour of upper part of visible window.

The drawing shows a typical Reflex Glass Level Gauge.
This instrument consists of a metal body, machined to have an internal chamber and one or more front windows (on one side
only of the gauge).
On each window a special high resistance plate reflex glass is fitted with sealing joint and metal cover plates hold by bolts
and nuts.
The chamber is connected to vessel with cross fittings and flanged, threaded or welded ends. Usually, between the instrument and its connecting ends, valves are fitted to consent shut-off piping and to disassemble the level gauge without to empty the vessel. Drain valves can also be fitted to cross
fittings device.
To avoid leakage in case of glass breakage, safety ball-check device can be provided.

Working Principle:
Reflex level gauges working principle is based on the light refraction and reflection laws.
Reflex level gauges use glasses having the face fitted towards the chamber shaped to have prismatic grooves with section angle of 90°. When in operation, the chamber is filled with liquid in the lower zone and gases or vapors in the upper zone; the liquid level is distinguished by different brightness of the glass in the liquid and in the gas/vapor zone. The reflex level gauges do not need a specific illumination: the day environmental light is enough. Only during the night an
artificial light must be provided.

We supply all type of water level gauge, including Bi-colour (Transparent) water level gauge, Reflex Water level gauge, Glass tube water level gauge, Tubular type water level gauge and Magnetic type water level gauge

The LKS power line lightning protector unit LP series is design especially for power on control instrument, Industrial or residancial. It come with a built-in temperature cut-out technology. The built in gas arrestor can also be widely used for any electrical network system. It absorbs surges only without affecting instrumentation signal and its come in standard DIN rail mounting.
c/w CE Certificate

Application
LP-CZ series socket power lightning protection device are applicable to the front side of various terminal consumer equipment of AC not more than 240V and rated current less than 10A, providing protection against over voltage arising from lightning to power supply line and short circuit. Standard IEC61643 and GB50343.

Main Features
• In-line series protection system
• 20kA 8/20 surge rating
• Three modes pf protection , L-N, L-PE, & N-PE
• Modularized design, standard socket design, convenient for installation and use.
• Introducing multilayer protection technology, strong protection ability, and high reliability.
• Built-in temperature fuse, safe and reliable
• Red pilot lamp on indication status.

c/w CE Certificate

The LKS lightning protector unit model LP-V is design especially for automation process control instrument system use. It use to protects both side of the equipments. The built in arrestor can also be widely used for transmission systems by current loops. It absorbs surges only without affecting instrumentation signal and its design for DIN rail mounting.
c/w CE Certificate

we are expertise in selling chart paper and pens in Malaysia since earlier 1990
Call us today, You can find the lowest price in the town and ex-stock item for any brand of the chart paper and pens you are looking for.

All kind of pressure gauge is available!!!

Our Capsule Low Pressure Gauge are design for measurement air or gas of low and negative pressure which non-corrosive.

These gauges use a capsule as its sensing element. The sensing element consists of two half capsules which are soldered together. The capsule element expands by subjecting to pressure. The expansion is converted into the rotary motion of pointer by a movement.

A safety valve prevents deformation of the capsule in case of overpressure suddenly.

All kind of Temperature gauge is available!!!

We supply and stockist of all the standard size gauge glass for water level gauge and sight glass for sight indicator.

Float Level switch, Ultrasonic level switch, magnetic float level switch, capacitance level switch, side mounting float switch, optical level switch, pressure level switch, mini float level switch

Ultrasonic level switch, capacitance level switch, Sounding Continuous Level Switch, Vibrating Probe Level Switch, Rotary Paddle level switch, Pneumatic Vibrator, Air Hammer, Light-Strip Meter

Looking for different type of Recorder? Look for us!!!
we have supply many type of recorder including Strip Chart and Circular chart
Call us today to find the most suitable for you and make a good choice!

Feature & Function:
This level indicator is assembling for indicating the Level Water Level Tank suction as Reservoir, Suction Tank and etc.
The scale and range is selectable and customize to the customer need. The material of housing is in Mild Steel and coated either by Hot-dipped galvanize or epoxy coating.


Specification:
Dial Size - 300mm, 400mm, 600mm and 900mm
Indication Unit - Meters or feet
Accuracy - 1% of full scale
Zero Stability - +/- 0.5% of full scale
Repeatability - +/- 0.5% of full scale
Working Temp - Up to 80 ˚C
Relative
Humidity - 90% RH
Optional - Back Cover
And indicator dial with
Luminous Marking
Level Range - 0 ~ 3, 0 ~ 4,
0 ~ 5, 0 ~ 6, 0 ~ 8, 0 ~ 10,
0 ~ 15, 0 ~ 20 & 0 ~ 30 meter


Application:
Suitable for water and others
Non-aggressive fluids.

Application:

Liquid Level Indicator (Cat and mouse Gauge) is a simple mechanical float operated unit which gives a clear visual indication of tank contents.

The standard Liquid Level Indicator is suitable for atmospheric tanks, low pressure tanks, or where necessary, to limit the emission of vapours, an optional 'oil seal unit' can be added, which will withstand pressure up to 8.5" wg (21.2mbar).

Benefits:

- Recommended for virtually any liquid.

- Suitable for non-metal tanks.

- Easy and quick installation.

- Low cost maintenance.

- Adaptable for floating roof or floating deck tanks.

- Sheave housing fitted with inspection cover for ease of maintenance.